Accuracy:
0.01 - 2 ppb: ± 0.1 ppb
2 - 10,000 ppb: ± 5%
Acidity:
< 50 ppm
Ambient Temperature:
5 - 50 °C
Analogue Outputs:
6 isolated, 0 - 20 mA or 4 - 20 mA; load impedance: 600 Ohm maximum
Connection: 0.644 - 1.29 mm² (24 - 16 AWG) wire; 0.644 - 0.812 mm² (24 - 20 AWG) recommended, twisted pair shielded wire
Calibration Method:
Automatic with known addition
Manual: 1 or 2 points
Dimensions:
681 mm x 452 mm x 335 mm (H x W x D)
Display:
Coloured 5.7” LCD
Electrode Type:
Sodium ISE (ion specific electrode) electrode and reference electrode with KCl electrolyte
Fuse:
Input power: T 1.6 A, 250 VAC
Relays: T 5.0 A, 250 V
Include Autocalibration?:
No
Include Cation Kit?:
No
Inlet:
Sample line and sample bypass drain: 6 mm O.D. push-to-connect fitting for plastic tubing
Chemical and case drains: 7/16 inch I.D. slip-on fitting for soft plastic tubing
Interference Phosphate 10 ppm:
< 0.1 ppb
Load of analog outputs:
600 Ohm
Lower Limit of Detection (LOD):
0.01 ppb
Maintenance Interval:
Every 90 days: refill electrolyte, reactivation, conditioning, and calibration solution
Material:
Polyol case, PC door, PC hinges and latches, 304/316 SST hardware
Max. Concentration of Suspended Solids in Sample:
< 2 NTU, no oil, no grease
For boiler sample type install approx. 100 µm filter
Measuring range:
0.01 ppb - 10,000 ppb
Mounting:
Wall mount
Number of analog outputs:
6
Number of Channels:
1
Number of relays:
6
Options:
Analyser only
Parameter:
Sodium
pH Range:
6 - 10 pH
Pollution Degree:
2
Power requirements (Hz):
50/60 Hz
Power requirements (Voltage):
100 - 240 VAC
Protection rating:
NEMA 4/IP65
Relative Humidity:
10 - 80%, non-condensing
Relay output:
6; type: not powered SPDT relays, each rated at 5 A resistive, 240 VAC maximum
Connection: 1.0 - 1.29 mm² (18 - 16 AWG) wire; 1.0 mm² (18 AWG) stranded recommended, 5 - 8 mm O.D. cable
Repeatability:
< 0.02 ppb or 1.5% reading (whichever is greater) within ± 10 °C variation
Response time:
From 0.1 ppb to 10 ppb: T90 ≤ 3 minutes, T95 ≤ 4 minutes
From < 1 ppb to 100 ppb: T90 < 2 minutes, T95 < 3 minutes (about 150 s)
Sample conditioner:
Di-isopropylamine (DIPA) (1 L/100 days) at 25 °C for a sample pH target of 10.5
Sample Flow Rate:
100 - 150 mL/min (6 - 9 L/h)
Sample Pressure:
0.2 - 6 bar
Sample Temperature:
5 - 45 °C
Storage conditions:
-20 - 60 °C
Warranty:
12 months
Weight:
20 kg with empty bottles
What's included?:
Hach NA5600sc Sodium Analyser, 1 channel, with 1 channel installation kit and user manuals, reference electrode sodium, sodium ion selective electrode, empty DIPA bottle, mounting bracket and screws used to fix the mounting bracket